Home > Products > Tech Info > Generic >
Jack Wabbit Quad Stationary Decoder in Stock and Shipping!
Tortoise Buddy
More AHD Speakers
NCE CAB06 Shipping Now, CAB06R In 2 Weeks
Team Digital Announces SMD84 Accessory Decoder
Why Decoders Run Away or Reset
Increasing Brass and Copper Prices Force CMX Price Increase
MRC New Products, New Prices
Lenz LH90 Throttle Back In Stock
AHD Welcomes The Lenz Agency Into the Fold
MRC's Tech 6 Breaks the DC/DCC Barrier
Power Pax:
Guaranteed Broadway Ltd and Sound Decoder Programming
CMX Clean Machine:
Track cleaning system, rated #1 by users
DCC Circuit Breakers & Auto Reverser


How to Rescue a Faulty Decoder

What to do When Decoders are Not Working:

The ability to change a decoders CV settings gives an engine a multitude of customized features. Many modelers only go as far as changing the decoder’s default address from 3 to the cab number. A common fear is that if you enter the wrong value, lose control, you may end up in limbo without the ability to recover or correct the problem. Also, sometimes a track short circuit may cause some decoders to get corrupted and not respond correctly. Good news! There is generally a simple solution. Most decoders have a way to restore the decoder CVs back to factory default settings ... much simpler than trying to figure out which CV was causing the problem!

According to the manufacturers, many of the decoders returned for repair could have been rescued if they had been first reset to factory settings. I talked with one decoder manufacturer who said at least 33% of their returned decoders are “fixed” by using the simple reset procedure.

Since the factory reset is not in the NMRA DCC standards or recommended practices, each manufacturer can do their own thing. If you do not know the manufacturer of your decoder, you can try reading CV8 on the program track. This is a read only CV that has the manufacturer's ID number (numbers shown in decimal).

Here is a chart that lists the most common IDs and reset procedures. For other decoders check the manual for CV and value used to reset to factory settings. All these decoders do support Ops Mode programming and can be reset on the mainline assuming you have control of the address.

If you do not have control of the address use the program track.


Mfg. ID in CV8

CV for reset + value



CV8 = 33



CV30 = 2



CV8 = 8

LokSound (ESU)


CV8 = 8

Train Control System


CV8 = 8 or CV30 = 2

SoundTraxx: DSDLC, DSX
Tsunami (1)


CV 30 = 2

MRC (New) (2)


CV125 = 1

QSI (1)


See Below

(1) Generally requires PowerPax, Programming Track Booster
(2) Generally is not reliable in Read-Back

How to Reset a Decoder

Start by determining the decoder manufacturer. On the program track read CV 8. Compare the number with the above chart for the ID (if you have a QSI decoder [ID 113] see the information below). Then write to the matching CV the value as shown in the chart (writing a number to CV 8 will not change the value in CV8 when you read it back). When resetting the decoder, it may respond by flashing the lights or tooting the horn. Resetting a decoder will change the address back to the default of 3. Try the decoder on the main line using address 3 to be sure everything is okay. Then you can start your programming.

QSI Decoders

The Broadway, Atlas, and Lifelike equipped with QSI (ID 113) DCC sound engines use a different reset procedure. Check the manual that came with the engine. Some use a magnetic “wand” for the reset. If there is no "wand" then open the engine or access hatch and find the reset jumper. Remove the jumper and restore the track power. There will be an audible acknowledgment from the engine at the end of the reset sequence (usually 3 toots of the whistle/horn). Replace the jumper and test out using address 3.

If a "wand" is present, locate the internal reset reed switch and place the "wand" over it for a moment. When track power is restored the engine will go through its reset procedure and let you know when done. To find the internal reset (reed) switch, place the engine on active track. Slowly move the "wand" over the top of the engine or tender until the engine alerts you, audibly responds, by a message.

QSI also has a software reset using the following multi step procedure:

(1) Place engine on main track if it is still responding to its address. If not responding you may need to use the program track.
(2) Set CV49 to 110
(3) Set CV50 to 255
(4) Set CV56 to 113
As engine resets you will hear the 3 toots. Test out the locomotive using address 3.

QSI also has some selective resets. Refer to the DCC Reference Manual for this information.

Tech Info
Broadway Ltd
CMX Products
DCC Specialties
Generic / Other
NCE Corporation
Pricom Design
TDP Associates
Copyright 2004 - 2019 by American Hobby Distributors. All Rights Reserved.